![accufast et tabber accufast et tabber](https://www.boggsequipment.com/wp-content/uploads/2017/11/Accufast_ET_Tabber_Neopost_SLB_Address_Labeler_112117082814-33.jpg)
- Accufast et tabber manual#
- Accufast et tabber full#
- Accufast et tabber professional#
- Accufast et tabber series#
goes in-line with ACCUFAST and other tabletop Labelers and Printers.uses 115 volts 2 amps 60 hz or 230 volts 1 amp 50 hz.runs a variety of 1” tabs: paper & frosted, circles & rectangles, on rolls with or without tractor holes.tabs pieces 5” to 16” wide, from 20 lb.Accufast KT2 Tabber Technical Specifications Tabs fold tight to the edge of the piece and do not drift from left to right. Different formats are selected with the touch of a button and tabs are automatically fed from 12 inch rolls and. The ET/R is designed to handle everything a mailer throws at it, from edge tabbing or top tabbing of self mailers to the specialty tabs needed to meet booklet requirements. Short paper path with no skewing adjustments etc. The ACCUFAST ET/R is the next generation of table top tabber. The shortest dimension feeds through the machine increasing production rates at any given speed
Accufast et tabber professional#
At speeds of 15,000 per hour or so, it is a stretch to refer to the ACCUFAST KT2 as a basic tabber – there’s a lot of the professional in the KT2.Īdvantages of Accufast KT2 Crash Tabbers It tabs pieces up to 1⁄4” in thickness and it rolls the waste up on a take up spool. It uses plain circular or rectangular tabs either opaque or clear. The ACCUFAST KT2 is a feature rich basic tabbing machine. All Accufast are proudly made in the USA. When you pair the Accufast KT2 tabber with the FX Feeder and 3FV conveyor, you have the most reliable tabbing system out there today.
Accufast et tabber manual#
The leading edge then comes in contact with the tab which has been fed down in front of the piece, pulling the tab from its backing paper.Īre you looking for operator manual for Accufact KT Tabber and XL labeler? Check out this page for information about operators manual.
Accufast et tabber series#
The Accufast KT tabber series are crash tabbers in which the edge of the piece to be tabbed is fed into the machine first. All of these modules are available from ACCUFAST.Accufast KT2 Tabber The Tabletop Tabber Series That Revolutionized the Industry The Accufast KT2 tabber is similar to the KT with the addition of another tabbing head, which allows you to apply one or two tabs in one pass.
![accufast et tabber accufast et tabber](https://www.boggsequipment.com/wp-content/uploads/2017/11/Accufast_ET_Tabber_Neopost_SLB_Address_Labeler_112117082814-11.jpg)
The ACCUFAST ET does both with the twist of a knob.īecause a self mailer often starts out as a single sheet of paper, the ET can easily become part of a mail production system that can include a paper folder, the ET, a transfer table and an ink jet address printer. The self mailer is pretty much as it always has been save for the fact that either top or edge tabbing is allowed. Just splice one stack of tabs to the next and run the whole thing, stopping for a few seconds occasionally to clear the waste paper spool. This eliminates much of the handling of tabs. Tabs are usually supplied to the ET in high volumes from a box of fan folded tabs located on the floor below the machine. The location of the tabs is automatically set based on the size of the piece being used and USPS specification. Tabs are applied based on the tab mode selected at the start of the run. Typically a feeder such as the ACCUFAST FX or ACCUFAST HDF is used in line with the ET and the booklets are fed spine first into the tabber. Booklet tabbing is most often an off line activity. The specification for the location of the tabs is quite precise. The regulations require at least 2 and usually 3 one and a half inch tabs to close the booklet for self mailing. The USPS defines a booklet as a folded mailer with a spine and some sort of device (staple or glue) to close the spine. As with most microprocessor-controlled machines, the FD 280 needs a few seconds to get itself ready to run.
![accufast et tabber accufast et tabber](https://www.boggsequipment.com/wp-content/uploads/2020/04/Accufast-ET-Dual-Head-Tabber-w-Accufrast-HDF-Friction-Feeder-033120110910-3.jpg)
This flow is monitored by a set of sensors and a microprocessor. The FD 280 depends on a smooth flow of both tabs and mail pieces. We've organized this presentation around the two major applications: Booklets and Self Mailers. Imitation tabs can be run on Formax Tabbers, but are not guaranteed to run problem-free.
![accufast et tabber accufast et tabber](https://oamequipment.com/images/uploads/products/ACCUFAST_ET_Tabber.jpg)
Accufast et tabber full#
Clean out the waste when it's full and splice on another strip of tabs when the first one runs out. Just select the correct Tab Mode, load the proper tabs, and feed pieces from whatever device you choose on the front end. Very little set up and operator interaction is required. The essence of the ET is that it tabs both booklets and self mailers with the appropriate tabs in the correct spots automatically. The ACCUFAST ET is a tabbing machine that has more uses than we have space to explain them.